Tip for removing the Bezel on a Seiko Monster

[samanator]

As part of assessing a modification I'm looking at doing I needed to figure out how to get the bezel off. After many google search variations I all I could deduct was that a thin blade knife needed to be place between the case and the bezel and twist the knife. The problem was nothing was fitting in the gap. I found a really thin blade knife that you can purchase for about $3 from any oriental grocery store (These are also great for slicing tomatoes). This sort of went in but no way was it going to be enough to be able to get any leverage. Then I stumbled on some thing, I was aligning the smooth indented grooves on the watch case with the smooth indented grooves on the bezel. Wrong, align the bezel so the smooth indented grooves on the case are aligned to the knurled (for lack of a better term) outward grips.
http://i248.photobucket.com/albums/gg166/samanator_2008/project/bez1.jpg?t=1219007666

Wile I don't have it in the picture I suggest putting electrical tape over the exposed part of the blade that are not und the case and bezel so not accidental scratches occur.

http://i248.photobucket.com/albums/gg166/samanator_2008/project/bez2.jpg?t=1219008111
The blade should slip right in all the way now. Second part of the tip take a pair of pilers and grip the back edge of the knife blade in the center where the blade has gone the deepest under the bezel and twist.

http://i248.photobucket.com/albums/gg166/samanator_2008/project/bez3.jpg?t=1219008163

The bezel will pop right off every time. Not a mark to be found. Be sure and watch that the retaining clip under the bezel does not fly anywhere.

(Sorry I had to stage these photos since I did not have someone to take them while I held the watch)

Please note depending on your work surface it is easier to set the watch on the edge when removing the bezel (Which I could not do in the pictures since I was by myself) and watch where you hold the watch so the blade does not do more than remove the bezel.

http://i248.photobucket.com/albums/gg166/samanator_2008/project/bez4.jpg?t=1219008199

This is good to do maybe once a year and then clean and lubricate the mechanism (mine was pretty bad after six years ).

When replacing make sure you have the pins in the clip aligned and the contacting surfaces lubricated and snap the bezel back into place. A press may be required.

[Fred Lee]

Michael,

Thanks for the info. I have an OM and am just about to try to pop off the bezel. Could you post some pictures for reference

[valvestem]

That's good info, maybe should go into our section on "how to's & references".

[Torrid]

My bezel isn't quite perfectly aligned. Is there anything I can do the clicking mechanism to make it line up?

[tsaroy]

Samanator,
Thanks for posting this...I joined last week so I could buy a watch (I've bought two now, hope this isn't an indication of my weakness.. and I happened on your post because the monster I bought had what felt like a bad clutch on the bezel. Sure turns out to be a lot more simple than I thought- got the bezel off and the two upward facing fingers on the spring needed a tweak further upward, and everything's fine. In fact, I repeated the process a few times until I was satisfied the bezel felt "right".
By the way, no press ( I've got to get one of those) for reinstalling the bezel, (this may seem kinda cave-man, so stop now if you're squeamish- I first tried using a mechanic's technique of heating (expanding) the bezel in boiling water, while cooling the mating surface with an ice cube- not necessary, and it didn't work with hand force. I lined everything up, and placed the watch face down on a linoleum covered concrete floor, and braced myself and used my weight to press my sock-covered heel on the back face- satisfying and distinct click into place. I'd say it was approximately 196 lb. of force. Probably wouldn't work with a domed crystal. Thanks again.
Regards,
Roy

[42Hz]

did this operation on my watch a few days ago and everything worked well thanks to this great guide! One thing though, there is a ruber o-ring inside the bezel and it managed to get squeezed between the watch and bezel, thought I used to think oil since the bezel became wery hard to rotate but then in noticed the missaligned o-ring!

So beware of the o-ring when pressing back the bezel!

tsaroy: Thanks for the tip to use the floor! Worked perfectly! =)

did a video when I removed the bezel, I try to post it here when it's edited.