Project 300: Dial and case design - Page 15
Like Tree59Likes

Thread: Project 300: Dial and case design

Page 15 of 27 FirstFirst ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ... LastLast
Results 141 to 150 of 270
  1. #141
    Yao
    Yao is offline
    Sponsor Yao's Avatar
    Join Date
    Dec 2006
    Location
    Pennsylvania, USA
    Posts
    1,582

    Re: Project 300: Dial and case design

    Quote Originally Posted by ffernand View Post
    Bill, any word on the survey results? Thanks
    The survey's have been closed and the preliminary findings are the watch will be smaller. I can't say how much smaller yet until I dig a little deeper into the results.
    Kent108 likes this.

  2. #142
    Member ffernand's Avatar
    Join Date
    Jul 2010
    Location
    Miami, Florida
    Posts
    61

    Re: Project 300: Dial and case design

    Bill,

    Thank you for the information. Look forward to the results...

  3. #143
    Member tmoris's Avatar
    Join Date
    Dec 2009
    Location
    Praha, CZ
    Posts
    763

    Re: Project 300: Dial and case design

    is the luminous bezel insert going to be the same as on paradive or will it have stronger luminosity?

  4. #144
    Member boostin20's Avatar
    Join Date
    Sep 2010
    Location
    MD
    Posts
    155

    Re: Project 300: Dial and case design

    ^I was wondering the same thing. Here's to hoping it glows like a torch.

  5. #145
    Member ASRSPR's Avatar
    Join Date
    Jun 2009
    Location
    USA
    Posts
    1,507

    Re: Project 300: Dial and case design

    As far as bezel lume goes, I always thought that the Paradive was pretty good. Compared to, say, my PRS-14.



    (Acrylic bezel version)

  6. #146
    Member Rusty_Shakleford's Avatar
    Join Date
    Jan 2011
    Location
    The Peach State
    Posts
    2,433

    Re: Project 300: Dial and case design

    ^^^ASRSPR, Great lume shot.^^^
    Hidden Content
    Follow Me

  7. #147
    Member tmoris's Avatar
    Join Date
    Dec 2009
    Location
    Praha, CZ
    Posts
    763

    Re: Project 300: Dial and case design

    Quote Originally Posted by ASRSPR View Post
    As far as bezel lume goes, I always thought that the Paradive was pretty good. Compared to, say, my PRS-14.
    (Acrylic bezel version)
    the picture shows overblown indices and hands and an ok bezel. that means that in reality the hands and indices glow normally whereas the bezel is rather darkish.. not comparing it to precista obviously.. I would like a bezel that can glow for many hours during the night, preferably readable early morning as well (just as i can read my SMP 2254.50 hands/indices any time of the night)

  8. #148
    Member ASRSPR's Avatar
    Join Date
    Jun 2009
    Location
    USA
    Posts
    1,507

    Re: Project 300: Dial and case design

    I didn't mean to suggest that it was just as bright (it is an 8 second rear-curtain sync exposure, after all). Certainly the hands are much brighter but as far as these things go, it's not too bad at all. I just never thought of this as a major point of concern for the Paradive. It sounds like Bill is suggesting some alternative approach to bezel lume though, so perhaps it'll be better.
    Last edited by ASRSPR; November 25th, 2011 at 19:35.

  9. #149
    Member
    Join Date
    Apr 2011
    Location
    Sunny AZ.
    Posts
    141

    Re: Project 300: Dial and case design

    I have been busy with life and haven't check up on our 300 progress. Any word on the surveys? Any new ideas being thrown about? Last I heard the watch was going to be on the smaller side of the proposed dimensions and while I'm still ok with it I hope the width isn't reduced by a lot.
    Have a merry Christmas and holiday season.
    Chris
    Seiko: 62MAS, 6105, 6306, 6139, BASM, FFF
    Marathon : GSAR
    Doxa: Anti-magnetic '45
    MKII: Project300 plank owner

  10. #150
    Member ffernand's Avatar
    Join Date
    Jul 2010
    Location
    Miami, Florida
    Posts
    61

    Re: Project 300: Dial and case design

    Have the survey results affected in any way the timeline of the Project 300? Would like to know how the survey results will affect the completion of the case design phase and thus help the project move forward.
    I would appreciate any input. Thanks!
    Merry Christmas to all.......

Page 15 of 27 FirstFirst ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts

    Search Engine Friendly URLs by vBSEO 3.6.0 PL2